Can I Install a Tub Myself? Considerations And Also Steps
Can I Install a Tub Myself? Considerations And Also Steps
Blog Article
This article in the next paragraphs in relation to How to Install a Bathtub is quite enjoyable. Check it out for your own benefit and decide what you think about it.
Mounting a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, and often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to eliminate the old tub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a home handyman's skills, although you will certainly need an assistant to move out the old bathtub and embeded in the new one. Make certain you have actually qualified on your own for the job as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is much better to take into consideration employing one prior to you start. Chances are you might require a professional plumber to make tube links.
This write-up will assist you mount a new tub in your shower room if you have actually already gotten a brand-new tub and do not need to transform the setup of your previous supply of water pipes.
Your devices and also material checklist must consist of the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the supply of water. After doing so, activate the faucets to drain pipes any water remaining in the system. The process of eliminating the existing faucets can be fairly bothersome due to the restricted access that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly need to be cleaned up of any type of old securing substance.
Before carrying on to fit the new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the faucet and also the various other end supplies a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, position the tap in the mounting opening in the bath/basin making sure that the washing machines are in place between the faucet as well as the sink. Protect the tap in position with the supplier supplied backnut. When the tap is firmly in position, the supply pipes can be connected to the tails of the taps. The faucets can either be linked by using corrugated copper piping or with regular faucet ports. The former kind must be linked to the tap ends initially, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been linked.
Installing the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the called for setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be attained by checking the level as well as adjusting the feet on the tub until the level checks out degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other tap.
Activate the supply of water and also check all joints and also new pipework for leakages and tighten them if essential. Fill the bathtub and additionally check the overflow electrical outlet and the typical outlet for leakages.
Ultimately, repair the bathroom paneling as described in the supplier's instruction manual. Tiling as well as sealing around the tub needs to wait until the bath tub has been utilized at the very least once as this will certainly resolve it into its last position.
Planning for the Setup
To start with, the supporting framework provided with the bath ought to be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is also practical to fit a sustaining plate under the faucets unit to avoid stress on the bath tub.
Fit the flexible tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make sure you use all of the supplied washing machines.
Link the catch to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last setting.
Tiling Around the Tub
In the location where the bathroom fulfills the floor tile, it is essential to secure the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to break a rigid seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, causing issues with moisture and possible leakages to the ceiling listed below.
You can select from a selection of coloured sealers to assimilate your components as well as fittings. They are sold in tubes and cartridges, and can securing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of soaked newspaper or soft rope. Remember to always load the bath tub with water prior to sealing, to allow for the activity experienced when the bathtub remains in use. The sealant can fracture relatively early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally quickly available on the marketplace. It is recommended to fit the ceramic tiles making use of waterproof or water resistant adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you really like more info about Installing A Bathtub? Try leaving feedback further down. We will be glad to hear your suggestions about this blog post. We hope that you come back again in the future. Feel free to take a moment to distribute this article if you liked it. Many thanks for going through it.
Get A Free Quote
Report this page